Feed the cans
Can format and infeed are matched to the selected machine.
CAN FILLER
MULTIMA LC
Can filling for larger production runs.
A counter-pressure long-tube filler for your canning line.
Enquire about this machine ↗Downloads ↓
MULTIMA LC
Can filling as a coordinated process.
MULTIMA LC is a rotary counter-pressure can filler with 12, 18, 24 or 30 filling stations. Before the can docks with the valve, the long filling tube introduces CO₂ to displace air. The can is not evacuated by vacuum. A CO₂ tunnel and bubble breaker can limit contact with ambient air on the way to the seamer. Can format, seaming technology and the complete line are specified together.
CansLong-tube counter-pressure technology
1,200–13,100Cans/h · indicative range
12 · 18 · 24 · 30Available filling valve counts
Calculated indicative range across machine sizes and 0.33/0.50 L containers: 50–105% of nominal output, rounded inwards to the nearest 100 cans/h. The table shows nominal outputs by size. Actual output depends on product, container and the complete line.
Fill and transfer
The can is filled and transferred to the seamer, with CO₂ management included in planning.
Form the seam
The selected seamer joins the can and lid before the container moves to outfeed.
OUTPUT DATA
Output by machine size.
Nominal outputs for Pilsner at 4 °C and 5.6 g CO₂/L, using containers suitable for MULTIMA LC and the selected configuration.
| Filling stations | 0.33 L | 0.50 L |
|---|---|---|
| 12 | 3,200 | 2,400 |
| 18 | 5,900 | 4,300 |
| 24 | 9,500 | 6,700 |
| 30 | 12,500 | 9,300 |
Net output of the complete line also depends on infeed, discharge, closing equipment and other operations. We agree the operating conditions and exact configuration together.
TECHNOLOGY IN DETAIL
Explore the machine in detail.
Explore the machine’s functions. Choose a point in the image or open a detail below.
Example configuration. Equipment and arrangement are defined for your project.
01Mechanical filling valve
The long filling tube first enters the can. Before the can docks with the valve, CO₂ flows through the tube and displaces the air inside. Unlike bottle filling, vacuum pre-evacuation is not used, because negative pressure would collapse the can. Counter-pressure filling follows.
02CO₂ tunnel
Open cans travel through a CO₂-supplied area between the filler and seamer. This helps limit contact between the product and ambient air.
03Bubble breaker
A directed CO₂ jet removes the upper foam layer before seaming. Settings are coordinated with fill height and the product’s foaming behaviour.
04Can stop
During a normal stop, the can stop prevents further containers from entering, allowing cans already in the machine to complete the intended process.
05Carousel spraying
Carousel spraying helps remove product residues in the machine area. It complements the cleaning procedures agreed for the system.
06Hygienic frame design
The base frame reduces horizontal surfaces so water and product residues can drain more easily. Its open construction supports access for cleaning and routine care.
YOUR CONFIGURATION
Configured for your production.
Four sizes
12, 18, 24 or 30 filling valves provide different configurations.
Seaming technology
The can, lid and seamer combination is selected together.
Line planning
Can supply, cleaning and downstream operations are included in the plan.
For the first discussion, tell us your drink, container, required output and available space. After discussing an indicative budget, we agree the scope for a quotation.
Cleaning and support in operation.
CIP-capable and suitable for steaming
Cleaning in Place means cleaning without dismantling components for the CIP process. This also applies to INVASA and CANVASA. Heat-resistant peroxide-cured EPDM seals allow steaming. We agree the cleaning agents, temperature and procedure for your configuration.
Remote access: you make the connection
For several years, our machines have been supplied with a modem in the control cabinet. Your LAN internet connection enables access through a gateway to our service team. Without that connection, external remote access through the modem is not possible. Telephone and video support are separate ways of helping you.
DOCUMENTS
Product data sheets
Overview and individual sheets for MULTIMA L, K, LC and 2in1, with 12, 18, 24 or 30 filling heads. Available in German and English.
Available sizes: 12 · 18 · 24 · 30
Receive data sheets by email ↗YOUR NEXT PROJECT
Your project with
MULTIMA LC.
A few details are enough: tell us your drink, containers, target output and plans.
sales@leibinger.eu ↗Mon–Thu 07:30–16:00
Fri 07:30–14:30
Fri 07:30–14:30
Your enquiry aboutMULTIMA LCDiscuss your project
Opening the form connects to HubSpot and transmits your IP address and browser information. We use your details to respond to your enquiry. This does not subscribe you to a newsletter. Form privacy information. You can also contact us by email or phone.
Alternatively, open the form directly ↗